The remainder of the installation is the reverse order of removal. The turning torque should be 8. Refill the power steering reservoir to the correct level. Secure the engine with a suitable engine lifting device. Connect the brake actuator connector.
Install the front right side fender apron seal. Sometimes the heater circuit will intermittently open or develop high resistance. If there is power at the computer, then there is a break in the harness between the computer and the sensor. Loosen, but do not remove the alternator mounting bolts. Bolts C to 41 ft. This marked Scion's world-first professional start in road racing, and the team led the race for a period of time in a 50+ car field.
Starting and Ignition 2004 Fig. Oil pump Page 25 Fig. Remove the bottom alternator mounting bolt and alternator. Using the brake line tool, connect each brake tube to the actuator with the bracket, as shown in the illustration. When retracting the tensioner, turn it clockwise slowly in 3 second or more. Ignition coil Engine appearance cover Alternator Accessory drive belts Negative battery cable 8. Remove the oil strainer and gasket.
Check the charge warning light circuit, as follows: A. The good news is that when this clutch goes out the transmission will still take you to where you need to go. The audio system has steering-wheel-mounted audio controls and compatibility with portable music players. Remove or disconnect the following: Front wheel Wiper arms Top cowl ventilator louvers Stabilizer links Wheel speed sensor 3. Install or connect the following : Lower control arm mounting bolts. Relieve the fuel system pressure.
Turn the crankshaft pulley until its groove and the timing mark on the front cover are aligned to set the No. Tighten to 71 inch lbs. Remove or disconnect the following: Steering column hole cover plate Intermediate steering shaft Front wheel Engine undercover Page 52 Tie rod ends Power steering hoses Front stabilizer links Lower control arms Front floor panel brace Center exhaust pipe Hood Engine appearance cover 5. Bolt A to 80 inch lbs. Connect the negative battery cable. Separate the axle assembly from the halfshaft. Allow system capacitor to discharge for two minutes before beginning any component service.
Install the cylinder head cover and remaining components in the reverse of the removal procedure. Drain the engine cooling system. Turn the crankshaft to gain access and remove the 6 torque converter mounting bolts. Spark plugs typically need to be replaced every season or 25 hours of use. Temporarily install the alternator and fan belt on each pulley, then adjust the belt, as outlined in the next steps.
Measure the cam height with a micrometer. Separate the transaxle from the engine assembly. Calculate the thickness of a new lifter so that the valve clearance comes within the specified value. The exhaust camshaft should measure as follows: A. Temporarily tighten the oil pump drive shaft gear with the nut.
More often than not, this is going to be the issue. Remove the stabilizer link 8. Refill the engine with oil to the correct level. Connect the positive + lead of the voltmeter to terminal B of the generator. At 29, the tC sports coupe had the lowest-average age buyer in the industry according to Toyota. Checking the stabilizer link 9. Remove the three mounting bolts to remove the oil pump assembly-2.
Check that the light goes off. Remove or disconnect the following: Front wheel Hub nut Wheel speed sensor Brake caliper Front disc Tie rod ends Lower control arm Axle from the hub assembly Steering knuckle from strut Lower ball joint Axle hub snap ring 3. Bolts B to 59 ft. The airbag will propel into the air if accidentally deployed and may result in personal injury or death. Install the oil pump assembly with a new gasket. Support the front crossmember with a suitable jack. Tighten to the nuts 54 ft.
Remove the exhaust camshaft bearing caps. The wiring should be the first place that you should check, as it will most likely be the problem. Before servicing the vehicle, refer to the Precautions Section. Install the brake actuator with bracket with the 3 bolts and tighten to 14 ft. Bolt identification for front suspension braces. If the same code resets, substitute a known good control module and retest. Remove or disconnect the following: Steering column hole cover plate Intermediate steering shaft Front wheel Engine undercover Tie rod ends Power steering hoses Front stabilizer links Lower control arms Front floor panel brace Center exhaust pipe Hood Engine appearance cover Page 57 Back to Top 5.