And I compared both sensors waveforms and no difference. Unplugged reads closed properly and putting a jumper into the 2-pin connector reads open. Checking the oil in a A4 Quattro is fairly easy and should be done once a month. The Tru Pointe is designed to be instantly responsive to all refrigerants. Prevents spillage during oil filter change and allows for drainage of oil from the filter housing. My dipstick tube is located underneath engine cover with a plug. I tried it again but it read empty the second time.
I have found a used Ecu very cheap I wonder why, I called my computer repair tech he told me some chips he can copy information from old computer to new one, but he has to see it. It came with no instructions. Tomorrow i will look into it. Personally, I prefer a manual check anyway, especially when topping up - a dipstick can never fail or go out of spec, any electronic sensor can, and eventually will. Thank drpeter, I did check the oil with proper dipstick to confirm and also removed the oil and added correct amount. Mario This is auto scan of a 2011 a4 2.
My dipstick tube is located underneath engine cover with a plug. Am I right to assume I can buy a dipstick from Audi, remove the plug and then insert and use as normal?. It was late in the day open the hood oil level reset to full, I started the car and drove around for 15 minutes scan data read normal and no warnings. The Laser 4807 dipstick is compatible with your Audi 2. I'm a bit confused as to which dipstick I need, as it seems some of the early ones aren't compatible with the later engines, or not with the dipstick tubes under the engine cover? I have read in other forums that in order to check the oil level you need to warm the engine up up by driving something like 30-40 kms otherwise the sensor will not register a reading at all. I decided to replace the level sensor with no luck.
As much as I love to drive my car, this is some next level thing. Now my dipstick fits even under the engine cover just for when I need to use it lol Just to let everyone know, I have an Audi A4 B8 2009 2. To exercise your right, just write us indicating your name and email address. That one would gradually increase oil data to normal when key was turned on. But as soon key is turned off and back on the low oil comes up again. I did perform service reset. Can anybody else confirm the 06E115611H dipstick works with the 2.
My new A4b8 2010 arrived less the dipstick. No alarm activation when you open the hood either but when we opened the driver's door it alarmed properly. I would verify the engine oil level with the tool, then address ref: Technical Service Bulletin Transaction No. Under the Data Protection Act of 6 January 1978, you have a right to access and rectify data concerning you. Key on warm engine oil measures full inside hood open. If the oil in your A4 Quattro is dirty or smells like gasoline, you probably need an oil change. I even jumpered the relay.
But after key and vin adaption we had to change some coding again. Increase leverage Increased reach into deep pocket areas Forged convex head allows the user to rock objects front and back, and side to side. Set contains 8mm, 10mm, 12mm, 14mm and 16mm spline sockets for European axle shafts and transmission drain plugs. The car is not currently with us, but Im sure I can get access if there is anything we can do to help. Mario No i have not because we dont know what is causing it. Just to let everyone know, I have an Audi A4 B8 2009 2.
I found a solution at long last!!!! I reported this on this Forum but got no takers or interest. Check out Laser Tools dipstick part no 4807. I did let car sit for an hour after oil level was reset and I turned key on I was surprised to see that oil level read normal. Really handy, you can pop round and pick it up. I open the hood oil level reads normal and after two starts I get low oil message again. In addition to checking the oil level, you also want to look at the condition of the oil when you have the dipstick out. But come on Audi, you make amazing cars but ruin it with the smallest of things.
New part behaves the same as old part. The tool checks the oil levels on Audi 2. The number should be large so feel free to post the current value if you want us to break down the meaning. When you're adding oil to the engine you don't have to worry about making a big mess due to the internal baffle of the valve cover. Polished high carbon drop forged steel.
Perfectly mated cutter, heat treated to hold its edge. I went through the major modules 01, 02, 03, 05, 09, 17, 19, 46 and 56 and do not see any obvious coding conflicts. Hi just wanted to check I am purchasing a 2011 2. I can plug my old oil level sensor into the good working car and turn key on off many times and I will not get low oil on the display. Let us know what happens. I found a solution at long last!!!! So let me get this stright, I actually have to go on a fairly long trip just to check my oil level? All you have is a tube where a dipstick may appear to belong.