Error: 0xC004F069 on a computer running Microsoftwindows non-core edition, run 'slui. After installing and configuring as evaluation mode, it is often a requirement to upgrade it to full retail version. We decided to go ahead and activate it to the full version. In this box, enter the following command: cscript. If they are, how do I go about activating the server? It will prompt you to reboot. You agree that you must evaluate, and bear all risks associated with the use of this batch file including any reliance, completeness, or usefulness.
Retail version conversations are bit of difference. For additional information, see Print and Document Services See. When The trial period ended though, I went to Amazon and bought a copy. How To Convert Windows 2012 R2 Evaluation Versions To Full Retail Version Evaluation versions are trails editions for 180 days. If you see more than one edition in the right column, upgrade to either edition from the same starting version is supported. Are they not the same edition? It also summarizes the supported upgrade paths from previously licensed retail versions of Windows Server to Windows Server 2012. Windows Server 2012 R2 enables you to provide access to corporate resources and helps protect critical business information.
JuanMa seems to be correct and I will start over with the server tomorrow as a clean install. The operating system will shut down every hour. Windows Server 2012 Essentials: you receive warnings on the Desktop and on the dashboard, but the server does not shut down. This guide will show you how to change the product key for your Windows Server environment. Can anyone provide assistance or advice? Is there a way to make the new license key work without doing a clean install. View Windows activation status in the Windows activation area of the System page. I receive error: 0x8a10001 The specific product key could not be verified.
For Windows Server 2012 Essentials, you can run Setup and convert it to Windows Server 2012 Standard by providing the appropriate retail license key. You can also view to which target edition you can upgrade. Does anyone have a solution? Note: You can't perform the above steps if the copy of Windows Server 2012 installed is a domain controller. The server will restart twice. I had to setup my static ip address again and then activated it and that was it. Resources If you are not sure which product key is being used on a server, you can use third-party tools to verify which product key is currently installed.
With Windows Server 2012 R2, you can manage identities across your datacenter and federated into the cloud, provide flexible remote access to applications and resources, and define the resources and level of access users have to information based on who they are, what they are accessing, and what device they are using. This said, you were probably really stuck when you used that method, and if it did the trick that's great! I have downloaded and installed the Windows Server 2012 R2 evaluation version from Microsoft's Evaluation Center website. Has anyone found a way around this? Hyper-V Shut down and save all virtual machines prior to starting upgrade. The server will restart twice, and should be a retail version. !! Open an Administrator command prompt and type the following.
Before you attempt to convert the version, verify that your server is actually running an evaluation version. Trying it will not harm anything. The only requirement is purchasing the correct License and inserting the Product Key supplied by the License. If you have installed the eval version and want to change that version to a regular version all you have to to do is this. The following table summarizes these considerations. Tip For more information about Dism.
From the command prompt run slmgr. Simple and cost-effective Windows Server 2012 R2 also gives you resilient, multi-tenant-aware storage and networking capabilities for a wide range of workloads. For all editions, you have 10 days to complete online activation, at which point the evaluation period begins and runs for 180 days. Your Server should now be Activated. Stopping the sppsvc service, replacing the backedup files and restarting the sppsvc service. Then after the second command, I received a message saying that the product activation was successful.
I had trouble downloading and the response was superb. As you can see the current edition is Datacenter Evaluation. In control panel go to System and Security click on system. For all editions, you have 10 days to complete online activation, at which point the evaluation period begins and runs for 180 days. The server will restart twice. All editions of Windows Server 2012 are 64-bit only. Microsoft is providing evaluation versions to the register users.
Also, do I need to include the dashes in the product key, or just type all the characters together? Bipin enjoys writing articles and tutorials related to Network technologies. I convert the edition from standard to Datacenter by following the above procedure and by using the Datacenter Product key and after restarting the system i found no issue. Things are working as I want them to and would cause me much difficulty to reinstall everything. I appreciate any help you may give. Windows Server 2012 R2 offers exciting features and enhancements across virtualization, storage, networking, virtual desktop infrastructure, access and information protection, and more. Click View details in Windows activation for more information about your Windows activation status. I think I am toast.